IW-100GX-N eXtreme Power 11n 2.4Ghz 1×1 In Wall PoE Access Point is an easy-to-install and cost-effective solution for most of indoor wireless deployments. The high class access point is perfect for application in areas such as: hotels, offices, and Luxurious houses. The IW-100GX-N effectively works to extend the range and increase the performance of a wireless network. The IW-100GX-N provides a RJ-45 wired connection as well as both Wi-Fi wireless connection and RJ11 Pass-through functionality. The 100GX-N hardware equipped with to bundles Cerio CenOS 3.0 Software Core and support Cerio Wireless Management Software (CWMS), a network administrator can centrally manage the IW-100GX-N via a Web browser and SNMP MIB browser & VLAN tag. Included PoE, power and data are supplied to the unit using CAT5 Ethernet cable. It can be powered via PoE switch or PoE Injector when available. The Ethernet port supports Link-On and Cable Length Power Saving and Link-Down Power Saving when PoE is not available. The IW-100GX-N Structure (Form Factor) with bundle US or EU type faceplate is set to support In wall Mounting make up and installation.

The Software Built-in: CenOS 3.0 Introduction
CERIO’s GS Firmware uses the CenOS 3.0 core . The firmware’s main functions are Wifi application for Router + WiFi Access Point ( Includes Router AP+WDS) and Pure WiFi Access Point (Includes AP+WDS) and Point to Point / Multi Point WiFi Bridge and Bridge + Repeater Extension WiFi AP and WISP/CPE for Router + WiFi Repeater AP functions . The CenOS 3.0 core’s operational mode supports Router AP with WDS mode / Pure AP with WDS Mode / Pure WDS mode / Client Bridge + Universal Repeater Mode and WISP/CPE Repeater +AP mode. The CenOS 3.0 features that simplify deployment and reduce cost for continued maintenance of the indoor Access Point . The Cerio CenOS is undoubtedly your wifi application best choice.

IW-100GX-N CenOS 3.0 Software key Features

• Operation Modes : Router AP Mode, Pure AP+WDS Mode, Pure WDS Mode, Client Bridge Universal Repeater Mode, WISP Repeater + AP Mode
• Supports 8 Multiple-BSSID. And Support IEEE802.11f IAPP
• Maximum Security with 802.1X, WAP, and WPA2
• Integragted IEEE 802.3af Power over Ethernet (PoE).
• Max WDS Link x 8 (Wireless Distribution Service) for Pure WDS Bridge
• Bundles Wireless RF Signal Enable and Disable by time scheduling function to auto reboot function .
• Enable and Disable to control blinking of the devices LED lights
• Supports IEEE802.1d Spanning Tree
• Integragted IGMP v1/v2/v3 snooping functions and Support Web management
• IEEE 802.1Q Tag VLAN priority control  and SNMP v1/v2c/v3 , SNMP Traps Supported
• Ping Watchdog function support
• Support Hardware chipset base Watch Time Dog , The OS will be reboot by automatically before crash.
• Software UI support Auto reboot setting function , Can by Hour/Daily/Weekly to setting software Auto reboot
• Auto Channel Scan and support Scan other AP site survey Single information
• Bundles Cerio CenOS3.0 software Core interface allows for communicating with Cerio Wireless Management Software (CWMS) and CERIO AM-Series AP Management WLAN Switch or Access Controller hardware device of network management servers.
• Provide Traffic Monitor and Graphical GUI Status Interface.

IW-100GX-N CenOS 3.0 Software Specifications

Wireless Feature

• Supports IEEE802.11n，HT Tx/Rx Stream selection : 1 for 150Mbps(Tx),and 150Mbps(Rx) Transmission power control :  Layer 1~9
• Channel selection : Manual or Auto
• IEEE802.11f IAPP : to facilitate faster roaming for the stations among different APs nearby
• No of associated clients per AP : 32
• Supports 8 virtual BSSID and associated clients per AP to 32 and the Pure WDS Max. 8
• IEEE 802.11d -Multi country roaming
• IEEE802.1Q VLAN tag support
• IEEE 802.11e WMM QoS ,COS , Diffserv / TOS

Authentication/Encryption (Wireless Security)

• WEP 64/128/152 bit /EAP-TLS + Dynamic WEP , EAP-TTLS + Dynamic WEP, PEAP/MSPEAP + Dynamic WEP
• PA-PSK/TKIP,WPA-802.1x/TKIP, 802.11i WPA2-PSK/CCMP/AES 128/256bit, WPA2 (802.1x /CCMP / AES 128/256bit ), No. of registered RADIUS servers : 1
• Setting for TKIP/CCMP/AES 128/256bit (ASCII 63 & HEX 64 )key’s refreshing period WPA2-PSK/CCMP/AES, WPA2(802.1x /CCMP / AES)
• Hidden SSID broadcast support
• Access Control list (ACL) by MAC and IP Address

Quality of Service

• IEEE802.11e WMM
• IGMP Snooping V3 Support
• DiffServ/TOS , COS, IEEE 802.1Q Tag VLAN priority control

Management

• On line client status monitoring
• Real time traffic monitor and status reporting supported
• Web-Based management interface, Intuitive Web Management Interface
• Supports Firmware Upgrade via Web , Reset to Factory Defaults
• Supports SNMP v1/v2c/v3 , MIB II
• SNMP Traps to a List of IP Address
• Supports Event log and Administrative Access : HTTP and HTTPS/SSL,SSH and supports CLI access via Telnet Management

IVLAN Tag / SNMP v2c/v3 and Web Based Management interface

Besides supporting IEEE 802.1Q Tag VLAN priority control, the users can also easily handle network management and maintenance tasks through this unit. The browser interface permits users to monitor node conditions, link quality, manage traffic flow, and view event logs of the IW-100GX-N units. The web based management interface also allows Network administrators to easily configure, update, and monitor every IW-100GX-N station. SNMP private MIBs are available for advanced users that prefer to manage devices through their own network manager.

The Software Bundle: CenOS 4.0 Introduction

CERIO’s NGS Firmware uses the CenOS4.0 core. The firmware’s main functions are web login authentication and Thin Access Point (TAP) modes. CERIO’s CenOS 4.0 Access Point uses hotspot technology importing concepts. Main functions include authentication login support remote RADIUS Server, local user account, OAuth2.0 account and guest login in AAP mode.

Cerio’s (Thin AP) wireless base station TAP function supports only GUI state monitor displays when acting as a Thin Access Point. Once this setting is operational, the device ends all NGS centralized control and management functions and operates strictly under the control and management of other supervising systems such as an AP utilizing CAP (Controller Access Point) mode. The thin AP deployment architecture acts to effectively improve network efficiency, and reduce security concerns of information theft from wired/wireless invades. Because no settings are stored in a Thin AP, device theft or invader intrusion would pose no threat to the networks security.

Controller Access Point (CAP)- AP manager Administrators should use CAP mode to simultaneously managed APs of AAP and TAP mode. Centralized APs management enables control of Wi-Fi function / security / users authentication / firmware upgrade / system time / traffic monitoring / and system information. TAP mode supports GUI status monitoring, allowing administrators to facilitate audit APs. CERIO’s NGS Firmware also supports load balance management through TAP mode (Real-time user limitation).

IW-100GX-N Hardware Key Features

• 800mW at 2.4Ghz Output eXtreme High Power
• IEEE 802.11n 1Tx / 1Rx Design, Bandwidth of up to 150Mbps(Tx), 150Mbps(Rx) link rate
• Integragted IEEE 802.3af Power over Ethernet (PoE) in this device.
• Ethernet RJ45 x 2 port connector and Phone RJ11 x2 port design

IW-100GX-N Hardware Application

In Wall Mounting Application

Desk Mounting Application

Main Unit with EU-Type Faceplate For Europe / China Specification